Network Surge Arrester
Home » Lightning Products » IT Surge Protection » Network Surge Arrester
Instruction
♦ TS-RJ45 Series Single Channel Ethernet Surge Protection Device (SPD) for RJ45 Network Protection (CE Compliant)
(8 Channels/Ports or 16 / 24 Channels Rack mount Ethernet Surge Protector) Available to make.
INTRODUCTION:
TS-RJ45 Network Cable Surge Protector is designed to protect network equipment from interruption caused by surge current according to IEC 61643-21; GB 18802.21; YD/T 15420. Mainly used for network equipment, e.g. Computer,Switch, Router, HUB, Modem and so on.
Similar / Related Products:
♦ Dimension of TSTLP Network cable lightning arrester (SPD)
♦ Basic Circuit Diagram of TS-RJ45/5/8 Network Surge Arrester
♦ Technical Data of RJ45 Surge Protection Devie
Model |
|
TS-RJ45/5/8 |
TS-RJ45/24/8 |
Nominal voltage |
Un |
5V |
24V |
Rated voltage (max. continuous DC voltage) |
Uc |
6V |
30V |
Rated voltage (max. continuous AC voltage) |
Uc |
4.2V |
21.1V |
Lightning Impulse Current (10/350) |
Iimp |
0.5KA |
0.5KA |
Nominal discharge current (8/20) |
In |
0.3kA (line-line) 0.3kA (line-PG) 2.5kA (shield-PG) |
0.1kA (line-line) 0.1kA (line-PG) 2.5kA (shield-PG) |
Max. discharge current (8/20) |
Imax |
0.4kA (line-line) 0.4kA (line-PG) 5kA (shield-PG) |
0.2kA (line-line) 0.2kA (line-PG) 5kA (shield-PG) |
Voltage protection level at In |
Up |
≤35V (line-line) ≤35V (line-PG) |
≤60V (line-line) ≤60V (line-PG) |
Voltage protection level at 1kV/ms |
Up |
≤13V (line-line-PG) ≤700V (shield-PG) |
≤45V (line-line-PG) ≤700V (shield-PG) |
Response time |
tA |
≤1ns (line-line) ≤100ns (shield-PG) |
|
Bandwidth |
fG |
165MHz |
|
Max. data transmission rates |
Vs |
100Mbits/s (Cat 5) |
|
Operating temperature range |
|
-40°C...+80°C |
|
Connection (input / output) |
|
RJ45 shield socket |
|
Pining |
|
1/2, 3/6, 4/5, 7/8 |
|
Earthing via |
|
Earthing screw |
|
Mounting on |
|
35mm DIN rail |
|
Enclosure material |
|
Aluminum |
|
Standards |
|
IEC 61643-21; GB 18802.21 |
|
Certification |
|
CE(LVD,EMC) |
♦ MAIN CHARACTER
1, For protecting computer data transmission system, telecom / network equipment system and so on
2, Good discharge capacity, low voltage protection level
3, Quick response, high transmission speed, low signal attenuation
4, RJ45 connection, easy for installation
INSTALLATION INSTRUCTION 1. This network surge arrester is connected in series to the protected device. 2. Mount the surge arrestor on 35 mm DIN rail. 3. The out terminal should be connected to the protected devices. 4. The lightning arrester's earthing terminal must be connected to nearby earthing BusBar or the metal earthing enclosure of protected device. Regularly inspect the operating status, especially after lightning.Once the communication is off, electrician should check/replace the Surge Protection Device. |
INSTALLATION DIAGRAM |
WARNING: 1, The surge suppressor must be installed by electrically skilled person, conforming to national standards and safety regulations. 2, It is recommended that installation should be done under power off condition. |
- CONTACT US
0086 13926098193
0086 20 28819702 EXT 27806
[email protected]
Hongdiyuan Industrial Park, Wufeng Avenue, Linjiang Town, Jiangdong New District, Heyuan, Guangdong,P.R.C.
http://www.tslpro.com
+86 13926098193
F13926098193
tslpro.tstlp
-