TS-RSP Series RS485-RS232 Surge Suppressor

Model 

TS-RSP9 

TS-RSP15 

TS-RSP25 

TS-RSP37 

Nominal voltage 

Un

12V- 

5V-

12V-

48V-

Rated voltage (max. continuous voltage) 

Uc

15V- 

8V-

15V-

55V-

Lightning impulse current (10/350)

In

/

/

/

2.5KA (line-SG)

Nominal discharge current  (8/20) 

In

100A (line-SG) 

200A (line-SG)

100A (line-SG)

3KA (line-SG)

Nominal discharge current (8/20) 

In

100A (SG-PG) 

800A (SG-PG)

100A (SG-PG)

Max. discharge current (8/20)

I_max

200A (line-SG)

400A (line-SG)

200A (line-SG)

5KA (line-SG)

Max. discharge current (8/20)

I_max

200A (SG-PG)

1.3KA (SG-PG)

200A (SG-PG)

Voltage protection level at In  

Up

≤24V (line-SG)       

≤200V (SG-PG) 

≤16V (line-line)

≤16V (line-SG)       

≤16V (SG-PG)

≤24V(line-SG)       

≤200V(SG-PG)

≤120V (line-PG)

Voltage protection level at 1kV/ms  

Up

≤21V (l ine-SG)       

≤90V (SG-PG) 

≤11V (line-line)

≤11V (line-SG)       

≤11V (SG-PG)

≤21V(l ine-SG)       

≤90V (SG-PG)

≤100V (line-PG)

Bandwidth

10 MHz

4 MHz

10 MHz

22 MHz (Series impedance per line (R)

Response time 

t_A

≤1ns (line-SG)        

≤1ns (SG-PG) 

≤1ns (line-SG)        

≤1ns (SG-PG)

≤1ns (line-SG)        

≤1ns (SG-PG)

≤1ns(line-SG)        ≤25ns (SG-PG)

Max. data transmission rates 

Vs

1Mbits/s 

Operating temperature range 

-40°C...+80°C 

Relative humidity

≤ 95% (25°C)

Protective lines

Line: 8/ SG/PG

2 two-core lines

7/SG/PG

Line:7/8/25/26/27, PG:12/20/30

Pinning

Line: 1/2/3/4/6/7/8/9,    SG: 5 (standby lines disconnected)

2/9 1^st pair;      4/11 2^nd pair; 8:SG: 1:PG (standby lines disconnected )

Line: 2/3/4/6/7/8/20, SG: 7 (standby lines disconnected )

Line: 7/8/25/26/27 (standby lines disconnected )

Mounting in

D-Sub, 2 threaded screws

D-Sub, 2 threaded screws/35mm Din Rail

Connection (input / output) 

D-sub 9 socket/plug

D-sub 15 socket/plug

D-sub 25 socket/plug

D-sub 37 socket/plug

Shield earthing

Outgoing cable 1.5mm²x 300mm

Enclosure material

Plastic, metallised

Dimension

64mm x 35.5mm x 21mm

Standards

IEC 61643-21; GB 18802.21; YD/T 1542

Certification

CE(EMC, LVD)

NSTALLATION INSTRUCTION 

1. This RS485/RS422/RS232 surge suppressor is connected in series to the protected device, installation in the partition of LPZ 2-3 interface;

In order to prevent lightning induction, LPZ 0A -1 and LPZ 1-2 interface must install additional surge protection products.

2. The out terminal should be connected to the protected devices.

3. SPD's earthing lead must be connected to nearby earthing BusBar or the metal earthing enclosure of protected device.

4. After above, you should ensure the circuit is functioning.

Regularly inspect the operating status, especially after lightning. Once the communication is off, electrician should check/replace the SPD.

TS-RSP9 INSTALLATION DIAGRAM

TS-RSP15 INSTALLATION DIAGRAM

TS-RSP25 INSTALLATION DIAGRAM

TS-RSP37 INSTALLATION DIAGRAM

WARNING:

1. The device must be installed by electrically skilled person, conforming to national standards and safety regulations.

2. It is recommended that installation should be done under power off condition.