TS-SP24 Information Surge Protector

Model       

TS-SP5 

TS-SP12 

TS-SP24 

TS-SP48 

TS-SP60 

TS-SP110 

Nominal voltage

Un

5V

12V

24V

48V

60V

110V

Rated voltage

(max. continuous voltage)

Uc

6V-/ 4.2V~

14V-/ 10V~

26V-/ 19V~

55V-/

39V~

65V- /

 50V~

170V-/ 130V~

Nominal current

I_L

0.5A

0.5A

0.5A

0.5A

0.5A

1A

Lightning discharge current (10/350)

Iimp 

2.5kA (per line)

5kA (total)

Nominal discharge current (8/20)

In

10kA (per line

20kA (total)

Voltage protection level at Iimp

Up

≤30V (line-line) 

≤17V (line-PG)

≤60V(line-line) 

≤30V(line-PG)

≤90V(line-line)

≤45V(line-PG)

≤150V (line-line) 

≤75V (line-PG)

≤200V (line-line)

≤100V (line-PG)

≤600V (line-line) 

≤300V (line-PG)

Response time

t_A

≤1ns(line-line)

≤1ns(line-PG) 

≤1ns(line-line)

≤1ns (line-PG)

≤1ns(line-line)

≤1ns (line-PG)

≤1ns(line-line)

≤1ns (line-PG)

≤1ns(line-line)

≤1ns (line-PG)

25ns(line-line)

25ns(line-PG)

Bandwidth

f_G

1.6MHz

(AD-PG)

2.9MHz (AD-PG)

5.1MHz

(AD-PG)

8.5MHz (AD-PG)

10.8MHz

(AD-PG)

24.0MHz

(AD-PG)

Series impedance per line

R

1.4 Ω

1.9 Ω

2.2 Ω

2.2 Ω

2.2 Ω

0.4 Ω

Capacitance

C

3nF (line-line)

5nF (line-PG)

1nF (line-line)

2nF (line-PG)

0.7nF(line-line) 

1.3nF(line-PG)

0.3nF(line-line)

0.6nF (line-PG)

0.3nF (line-line)

0.6nF (line-PG)

0.2nF(line-line)

1.4nF (line-PG)

Operating temperature range

-40°C...+80°C

Relative humidity

≤95% (25°C)

Cross-sectional area

Max. 2.5mm² flexible

Mounting on

35mm DIN rail

Enclosure material

Yellow thermoplastic, UL94-V0

Standards

IEC 61643-21; GB 18802.21; YD/T 1542

Certification

CE (LVD, EMC)

INSTALLATION INSTRUCTION 

1. The signal lightning arrester is connected in series to the protected device.

2. Mount the SPD on the 35 mm DIN rail.

3. The out terminal should be connected to the protected devices.

4. There is a earthing terminal in each side, and it is recommended to use the one at output side; earth lead must be connected to the earthing system, ideally using 2.5mm²cable. The cable should be as short as possible.

5. After above, you should ensure the circuit is functioning.

Regularly inspect the operating status, especially after lightning. Once the communication is off, electrician should check/replacethe SPD. 

TS-SP Series Surge Arrester INSTALLATION DIAGRAM

WARNING:  

1. The device must be installed by electrically skilled person, conforming to national standards and safety regulations. 

2. It is recommended that installation should be done under power off condition.